BoomworksHydraulics · Kenner LA(504) 385-9868

Boom truck hydraulic repair in New Orleans, LA

Call (504) 385-9868

Boomworks Hydraulics rebuilds boom truck hydraulics for New Orleans from our bench in Kenner, with mobile service for the failures that will not wait for a tow.

New Orleans works its boom trucks hard. Port drayage and terminal maintenance along Napoleon Avenue and France Road, roofers flying shingles over Uptown, riggers setting rooftop units downtown, and the film industry staging set pieces all lean on truck mounted cranes, and every one of those booms lives on hydraulic pressure.

Port adjacent work adds a corrosion problem the rest of the metro does not have. Trucks that stage near the river and the Industrial Canal live in salt heavy air, and chrome rods pit faster there than anywhere else we service. A pitted rod cuts seals on every stroke, so port fleets reseal more often unless the rods are kept coated and stowed.

Getting a repair truck to a job inside the city is its own skill. We run mobile service into Orleans Parish daily and know which terminals gate us in quickly. For downtown work we schedule around load windows so your crane is not blocking a lane while we bleed a circuit.

The high ticket work here is full system rebuilds on older port and construction cranes: pump, valve bank, and cylinders done together so the machine leaves with one warranty instead of three unresolved leaks.

Working on booms inside the port

Terminal operators at the port measure downtime in vessel hours, not truck hours. When a terminal crane truck goes down during a working vessel we have brought the rebuild bench to the truck, swapped in exchange cylinders, and finished the original units afterward.

Searching hydraulic repair near me from a New Orleans job site? Here is what happens next

A phone call gets a tech rolling to the truck, and a truck that is down on a job inside Orleans Parish is dispatched the same day. Kenner to the Port of New Orleans is twenty minutes on I-10 outside rush hour, the Industrial Canal and France Road a few minutes more, and we run that route often enough to know which gates move. Tell us the make of the crane, what it is doing or not doing, and the cross street, and we dispatch with the hose stock, fittings, fluid, and gauges that match the symptom.

The first thing we do on site is measure, not guess. Gauges on the circuit, a leak down timed with a watch, a look at the fluid in the reservoir. From that we tell you whether the fix happens where the truck sits (a hose, a fitting, a holding valve cartridge, a relief setting) or whether a component comes off and goes to the Kenner bench. Either way you get a number before anything is opened, and the emergency call out is credited toward the repair when you approve it on the spot. The ranges are the same ones published in our cost guide and in the article on who offers upfront pricing for boom truck hydraulic rebuild.

Which hydraulic repairs get done on site in New Orleans, and which go to the bench?

Hoses, hard line, fittings, holding valve cartridges, relief resets, and fluid service are finished on site, usually in one visit. Cylinders that are bypassing, pumps that have lost flow, and control valve banks with worn spools come off the truck and go to the bench, because a reseal done in a gravel lot on Almonaster or on the terminal apron is a gamble with grit in the packing. For a port or construction crane that cannot wait, we bring exchange cylinders where we have them and rebuild the originals afterward.

A truck that drifts, creeps, or will not hold a load should stop working until it is looked at. Drift is a cylinder or a holding valve bypassing, and bypass gets worse under load. Searching for the nearest shop is the right instinct, but the nearest shop also needs a bench, a pressure test rig, and a written number. Our note on what to look for before you hand a boom truck to a hydraulic shop lists the checks, and they apply to any shop in the city, not only ours.

Orleans Parish coverage

Regular routes cover the Port of New Orleans, Napoleon Avenue Container Terminal, France Road, the Industrial Canal, Tchoupitoulas Street and Almonaster Avenue, with ZIP codes 70112, 70113, 70114, 70115, 70117, 70118, 70119, 70122, 70126, 70129, 70130 inside standard coverage. Pricing is identical to the rest of the metro and published in the cost guide: no zone surcharges, and the emergency call out range covers the whole service area.

Nearby crews also use our Kenner, Harahan, Metairie pages for the corridors they work across parish lines.

New Orleans crane hydraulic questions

Can you service trucks inside the Port of New Orleans?

Yes. We run mobile service to the Napoleon Avenue and France Road areas regularly and can coordinate gate access with your terminal. For working vessels we prioritize the call like the emergency it is.

Why do our rods pit so fast near the river?

Salt air. Moisture plus salt attacks chrome plating, and every pit becomes a knife edge that cuts seal packing on each stroke. Stowing cylinders when parked and fixing weeps early slows it down. Once pitting starts, rechroming or a new rod is the real fix.

What does a full system rebuild cost on an older crane truck?

Pump, valve bank, and cylinders together typically run $5,000 to $10,000 depending on the machine. It sounds like a lot until you price a replacement crane body, which starts around ten times that.

Do you do the hydraulic side of annual crane inspections?

We do the repairs that inspections flag and the documentation that inspectors want to see. OSHA requires annual inspection of these cranes, and leak down or drift findings usually land on a cylinder or holding valve we can rebuild.

Quote a New Orleans rebuild

Tell us the truck and the symptom. Written quote before work starts, or call (504) 385-9868 and get it on the phone.

Written quote before any work starts. We can take on 4 more bench rebuilds this month. Emergency mobile calls always get worked in.